Ink Well pad printer making package

Details

Ink Well pad printer making package:

Including:

1 Manual ink Well pad printer
1 Exposure machine
20
photopolymer plates ( 75mm x 100mm)
2 Pads
20 A4 size Transparent films
( for injet printer or laser priter uses )

Open inkwell printer

Open ink well systems use a trough (ink well) for the ink supply, located behind the printing plate. A flood bar pushes a pool of ink over the plate, and a doctor blade removes the ink from the plate surface, leaving ink on the etched artwork area ready for the pad to pick up.

AD:blade is very cheap, waste ink,

Sealed ink cup printer

Sealed ink cup systems employ a sealed container (ink cup), which acts as the ink supply, flood bar and doctor blade all in one. A ceramic ring with a highly polished working edge provides the seal against the printing plate.

AD: ceramic ring is expensive, save ink.

Advantages of Photopolymer Plates making:

1. Good for the environment, no need chemicals.
2.Make clich making process easier to operate.
3.Save money for you, no need of chemicals and no steel coating machine.

Photopolymer Plates

The plate material is UV photosensitive and when exposed to an ultraviolet light through a high contrast negative, the U.V. cross links the polymers and hardens the image.

The unexposed portion of the negative is washed off in plain water, dried and post exposed. the plate is ready for the press in less than thirty minutes.

1:Pad Printer (Inkwell) ONE Unit

TECHNICAL PARAMETER:

Max printing area 80×80mm

Steel plate size 100×100mm

Max workpiece length 150mm

Level stroke 100mm

Pad vertical distance 60mm

Printing speed 400pcs/hr

Out dimension 400×200×500mm

Machine net weight 27kg

 

Free two pads

2:UV Exposure Unit : ONE Unit

Main features:

User-friendly desktop design with long-term life span Parameters.

6 UV fluorescent tubes

Exposing area: 10.23"x8.26"(260x210mm)
Voltage: 110v/220v
Light power: 48W (8W x 6 tubes)
Time Range: 0-5.5 mins
Machine size:11.82"x11.8"x29.5"(30x29x75cm)
Net weight: 12Lb(5kg)

3:Polymer plates: 20 sheets

Size: 75mm x 100 mm(for our ink well pad printer )

If you need more, can buy from our store:

  • Providing a good do-it-yourself option. These are typically used in short to medium production runs.
  • Water washable No solvent used!!

     

  • High durability, Allows printing very fine lines and big solid lines together, by using 300 lpi screen available.

     

  • High Reproductivity

     

  • Cost Effective

4:Transparent films: 20 SHEETS

( for ink-jet printer or laser priter uses )

If you need more, can buy from our store:

Any Epson、HP、Canon ink-jets printers can use it.

This Film is a specially coated,clear film that absorbs quick drying inkjet ink, and controls the shape of fine lines and half tones,can be used to make stencil in screen printng,hot stamping and pad printing.Ink-jets achieve better quality.

Print on the coated (matte) side of the film!
For the unique high-tech solution, they can not be conglutinated with each other when folded together. The image is well-resisting and suitable for storage.

Note 1: This film also can be used in your laser printer
Note 2: Your wet finger will stick to the coated side.
Note 3: Printing side is the non-smooth side

A4 8"x12" (210x297 mm)

Polymer plates Pad Printing Plate Making Process

1.Contact with Positive film

Remove cover film slowly and place positive film onto undeveloped plate.
Use positive film having optical density of not less than 3.0.

2.Exposure

Expose plate, through positive film, to UV light having 360 nm wave lengths for 1-2 minutes.

3.Contact with screen film

Remove positive film and place screen film on undeveloped plate.
240 and 300 lpi screen films are available and are supplied by our distributor in your country.

4.Exposure

Expose plate, through screen film, to UV light having 360 nm wave lengths, for 5-6 minutes.
Give longer exposure time, if shallower cell depth is required.

5.Wash-out

Remove screen film.
Wash-out exposed plate with water, at 15-25 for 0.5-2 minutes.
If wash out unit is not available, you can wash it out with running tap water.

6.Drying

Dry the plate in a hot-air dryer after removing the surface water by sponge roll or compressed air at 50-70 for 5-10 minutes.

7.Post exposure

Expose the dried plate to UV light again for 5-10 minutes in order to get stability.

General Hints:

  1. Gloss film as well as matted film can be used.
  2. Good contact between film and plate is essential.
  3. Treat films carefully as any kink will be reproduced on the developed plate.
  4. Check film and plate without any dust before exposure.
  5. Minimize the pressure of doctor blade to enjoy longer durability of plate.
  6. It can be used in inkwell system and closed ink cup system.

Important notes about making printing plates:

* The first exposure time on the film positive determines the overall depth of the ink well. The SHORTER the exposure time the deeper the printing plate.
* The second exposure on the film positive determines the amount of ink, the size of the dot and the spacing between the dots.
* Reducing the 2nd exposure time on the screen will reduce the height of the dot and will let more ink transfer
* You can control the printing effects by varying halftone screens:

Shipping

 

-When payment received, shipping will be made within 3 business days
- Please note your phone number and your address on Paypal for shipping , when special status happened, shipping company will call you.
- Seller is responsible for all damage on delivery.
- We ship items out Monday-Friday.
- Shipping is NOT available to P. O. Boxes.
- Items are NOT shipped out on Saturday or Sunday.
Refund policy
We will accept returns on all items within 30 days of you receiving the package. Please notify me of your intention to return the package within that time so We know to look for the package and can have your refund ready to send to you when I receive the package back. Refunds will be for item cost only shipping and handling will not be refunded. Item must be in the same condition as when item was sent.

Shipping and handling in any case are not refundable.
Warranty policy
- One year warranty from you receive the item.
- Warranty covers whole machine, includes electrical, mechanical.
- Any warranty shipping cost to us is responsible by buyer.
- Any shipping cost to buyer is responsible by us.

- Service center located in Toronto , Canada. Spare parts are available upon providing parts number and name.
Policies & Terms:

* Asking Questions email: This email address is being protected from spambots. You need JavaScript enabled to view it.

We make all attempts to answer emails within 24 hours.

*Feedback Policy
We leave feedback after the transaction is complete and ask that you do the same.

Please leave a positive feedback for us if everything is as described in our auction and policy, and we'll promptly do the same for you in return.

If anything is other than as described in our auction and policy, please contact us via email right away so that we can look at the issue and arrive at an agreement before leaving poor feedback.

In response to customer requests, we have developed Online Parts Order System in Toronto , an ongoing program where we will be stocking the majority of parts for our machine:

We are committing to our customers that we will have "The Right Parts at The Right Price at The Right Time."

These efforts will bring to our customers:
Convenient 24/7 ordering
Fast delivery

Click here, know more about us.